Angular contact ball bearings / single row / MISUMI (B7000)

Volume Discount

MISUMI

Product Details:

Manufacturer part number: B7000

Brand: MISUMI

Price: 6.55 €

Delivery time: Same day

Technical Data:

I.D. d: 10 φ

O.D. D: 26 φ

Width B (or T): 8 mm

Basic Load Rating Cr (Dynamic): 5350 N

Allowable Rotational Speed: 23200 1/min

Order quantities extended (D-JIT)

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

B7000

Drawing / Specifications
3D Preview 3D preview is available after complete configuration
Part Numbers
More Information
Catalog
Technical Information

Back to the Category Ball Bearings

Technical Drawing - Ball Bearings

Angular Contact/Standard Grade/Single:Related Image

For details on the tolerance and allowable values of inner and outer rings, >> P.2243

Available dimensions and tolerances can be found under the tab More information.

Basic Properties (e.g., material, hardness, coating, tolerance) - Ball Bearings

Material: EN 1.3505 Equiv.

For further specifications please see the More information tab.
Information on tolerances and rotational accuracy of the radial bearings can be found in the following PDF: Ball bearing table / tolerances as PDF

Composition of a Product Code - Ball Bearings

Part Number

B7000

General Information - Ball Bearings

Ball bearing - deep groove ball bearing - axial bearing - axial ball bearing - axial groove ball bearing - angular ball bearing - spherical ball bearing - tension bearing

Ball Bearing Selection Details

- Ball material: steel, stainless steel, ceramic, plastic, glass, chrome-plated

- Type of bearings: axial ball bearings, thin section bearings, spherical ball bearings, deep groove ball bearings, single-row angular ball bearings, double-row ball bearings, tension bearings, four-point bearings

- Outer ring: flat, spherical, with flange, annular groove, U-groove, V-groove

- Properties: heat-resistant, non-magnetic, corrosion-resistant, dust-proof, vacuum, high speed

- Inner diameter: 2 mm to 50 mm

- Outer diameter: 5 mm to 110 mm

Ball bearing designation (suffix):

In addition to the dimensional designation of the ball bearing, ball bearings often also have a designation for a cover disc or sealing disc. The following names are the most common names of various manufacturers that can be selected in the MISUMI online shop.

- Double-sided sealing washer: 2RSH/2RS1, 2RSR/C-2HRS, DDU/DD
- Single-sided sealing washer: RSH/RS1, RSR/C-HRS, DU
- Double-sided sealing washer with low friction: 2RSL/2RZ/VV
- Double-sided cover disc: 2Z/ZZ, 2ZR/C-2Z
- Single sided cover disc: Z, ZR/C-Z/Z

Description/Basics

Rolling bearings

Rolling bearings are generally divided into ball bearings and roller bearings. Ball bearings are a popular type of rolling bearings due to their high permissible speed and low friction.
In the MISUMI online shop, you can purchase ball bearings that can be customized to your applications and environmental conditions. Our ball bearings are available in different materials and in a combination of different materials (hybrid bearings). In addition, MISUMI offers ball bearings already integrated into the housing as bearing housing.

Grooved ball bearings

Grooved ball bearings are the most commonly used rotary rolling bearings. This type of ball bearing is ideally suited for supporting rotating machine elements. A grooved ball bearings are intended for load bearing of radial forces and light axial forces. Grooved ball bearings are designed for high speeds and are used in a wide variety of industrial applications and designs. MISUMI already offers ball bearings integrated into housings and holders as bearing housings.

Areas of Application

Ball bearing - chemical resistance

Chemical resistance		Plastic ball			Metal ball		Ceramic ball
Bearing rings		UHMW	PEEK	PTFE	EN 1.4125 equivalent	EN 1.4301 equivalent	EN 1.4125 equivalent	EN 1.4542 equivalent
Cover plate		-	-	-	EN 1.4301 equivalent	EN 1.4301 equivalent	EN 1.4301 equivalent	EN 1.4301 equivalent
Bearing balls		Glass	Ceramic (aluminum oxide)	Ceramic (aluminum oxide)	EN 1.4125 equivalent	EN 1.4301 equivalent	Ceramic	Ceramic
Ball cage		UHMW	PEEK	PTFE	EN 1.4301 equivalent	EN 1.4301 equivalent	Fluoroplastic	Fluoroplastic
Acids	Hydrochloric acid	suitable to a limited extent	good	very good	unsuitable	good	suitable to a limited extent	good
	Sulfuric acid	suitable to a limited extent	good	very good	unsuitable	very good	good	very good
	Nitric acid	suitable to a limited extent	good	very good	unsuitable	very good	good	very good
Bases		unsuitable	very good	very good	unsuitable	very good	good	very good
Solvents		very good	very good	very good	unsuitable	very good	good	very good
Salt water		very good	very good	very good	unsuitable	very good	good	very good
Water		very good	very good	very good	unsuitable	very good	very good	very good

Comparison Table The ball bearing comparison table is provided for comparison purposes only (consider the lubricant and the sealing washer separately).

Ball bearing materials

In the MISUMI online shop, ball bearings are available in cost-effective rolling bearing steel, corrosion-resistant stainless steel and stainless steel. Furthermore, our product range includes various hybrid bearings in the following combinations: metal & ceramic, plastic & ceramic, plastic & glass.

Our various materials offer good resistance to various environmental influences. Our ball bearing shop includes the ball materials stainless steel, steel, UHMW, PEEK, PTFE, ceramic and glass.

Instructions for Use / Installation Information - Ball Bearings

Installation Information

An incorrect assembly and disassembly can damage a ball bearing. Therefore, a suitable tool must always be used to assemble and disassemble ball bearings or roller bearings.
Ball bearings should not be assembled with a hammer, as this can deform the ball bearing. It is recommended using a suitable press. During pressing, the contact surface can be provided with lubricant to protect the surfaces and facilitate assembly.
It is best to use a bearing puller for disassembly.

Maintenance

The ball bearing in roller bearings should be inspected for damage during maintenance.
Before regreasing, a ball bearing should first be thoroughly cleaned.
Remaining contamination in the bearing can damage the ball bearing. As a rule, a ball bearing should not be completely filled with grease, as this can cause the bearing to heat up too much and can cause it to fail.
For encapsulated and sealed ball bearings, it is recommended to replace the bearing. Maintenance is not recommended due to the risk of damage to the cover place or seal.

Supplementary Article

Bearing Lock Nuts

Shaft nuts - lock nuts - steel shaft nut - stainless steel shaft nut - shaft with retaining nut - shaftnNut with clamp screw - shaft nut with grub screw - shaft assembly

Bearings with Housing

Bearing with housing - bearing housing - bearing units - ball bearing holder - ball bearing with housing - bearing housing with flange - shaft holder with ball bearing

Axles / Rotary Shafts

Rotary axis - offset rotary shaft - double offset shaft - female threaded shaft - keyway shaft

Drive shafts

Motor shaft - torsion shaft - shaft with collar - shaft with shoulder - offset shaft - keyway shaft

Plain Bearing (Bushes)

Plain bearing - maintenance free - plain bearing bushings - plain bearing bushing with collar - plain bearing bushing with flange - plastic bushing - plastic plain bearing bushing

Industrial Applications

3D printer industry

Automotive industry

Pharmaceutical industry

Packaging industry

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

Part Number
B7000

Part Number	Standard Unit Price	Minimum order quantity	Volume Discount	Standard Shipping Days ?	RoHS	I.D. d (φ)	O.D. D (φ)	Width B (or T) (mm)	Basic Load Rating Cr (Dynamic) (N)	Allowable Rotational Speed (1/min)	Basic Load Rating Cor (Static) (N)
	6.55 €	1	Available	Same day Stock	10	10	26	8	5350	23200	2600

Back to the Category Ball Bearings

Technical Drawing - Ball Bearings

Specification Tables - Ball Bearings

■Single Row

Part Number	d	D	B	r (min)	r₁ (min)
B7000	10	26	8	0.3	0.15
B7200	10	30	9	0.6	0.3
B7001	12	28	8	0.3	0.15
B7201	12	32	10	0.6	0.3
B7002	15	32	9	0.3	0.15
B7202	15	35	11	0.6	0.3
B7003	17	35	10	0.3	0.15
B7203	17	40	12	0.6	0.3
B7004	20	42	12	0.6	0.3
B7204	20	47	14	1	0.6
B7005	25	47	12	0.6	0.3
B7205	25	52	15	1	0.6
B7006	30	55	13	1	0.6
B7206	30	62	16	1	0.6
B7207	35	72	17	1.1	0.6
B7208	40	80	18	1.1	0.6
B7209	45	85	19	1.1	0.6
B7210	50	90	20	1.1	0.6

Part Number	Basic Load Rating		Allowable Rotational Speed rpm (Reference)	Pressure Cone Apex a	Relative Dimensions			Mass (g) (Reference)
Part Number	Cr (Dynamic) kN	Cor (Static) kN	Allowable Rotational Speed rpm (Reference)	Pressure Cone Apex a	Ds (min.)	dh (max.)	R (max.)	Mass (g) (Reference)
B7000	5.35	2.6	23200	9.2	12.5	23.5	0.3	23
B7200	5.4	2.71	22400	10.3	15	25	0.6	29
B7001	5.8	2.98	20800	9.8	14.5	25.5	0.3	25
B7201	8	4.05	20000	11.4	17	27	0.6	37
B7002	6.1	3.45	18400	11.3	17.5	29.5	0.3	35
B7202	8.65	4.65	17600	12.7	20	30	0.6	46
B7003	6.4	3.8	16800	12.5	19.5	32.5	0.3	46
B7203	10.8	6	15200	14.2	22	35	0.6	67
B7004	10.8	6.6	14400	14.9	25	37	0.6	80
B7204	14.5	8.3	13600	16.7	26	41	1.0	109
B7005	11.3	7.4	12800	16.4	30	42	0.6	93
B7205	16.2	10.3	11200	18.6	31	46	1.0	130
B7006	14.5	10.1	10400	18.8	36	49	1.0	135
B7206	22.5	14.8	9600	21.3	36	56	1.0	197
B7207	29.7	20.1	8000	23.9	42	65	1.0	287
B7208	35.5	25.1	7600	26.3	47	73	1.0	375
B7209	39.5	28.7	6800	28.3	52	78	1.0	411
B7210	41.5	31.5	6320	30.2	57	83	1.0	466

kgf=Nx0.101972

Products homepage

Basic information

Bearing Ring Shape	Angular Contact Ball (Single Row)	Materials of Inner and Outer Ring	EN 1.3505 Equiv.	Shield material and shape	Open Type
Outer Ring Type	Flat	Accuracy (JIS)	Class 0	Specifications/Environment	Standard
Load Direction	Radial	Number of Bearing Ring Rows	Single Track	Size Standard	Metric Series
Rolling Element Material	EN 1.3505 Equiv.	Combination of Angular Contact Ball Bearings	Single Track	Seal Part Structure	Open

This page is Angular contact ball bearings / single row / MISUMI, part number B7000.
You can find the detail information about specifications and dimensions on part number B7000.

Configure

1Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Stock

- Show only stock items
Clear

Basic Attributes

Type
- B7000
- B7001
- B7002
- B7003
- B7004
- B7005
- B7006
- B7200
- B7201
- B7202
- B7203
- B7204
- B7205
- B7206
- B7207
- B7208
- B7209
- B7210
Clear
I.D. d(φ)
10

12

15

17

20

25

30

35

40

45

50
Clear
O.D. D(φ)
26

28

30

32

35

40

42

47

52

55

62

72

80

85

90
Clear
Width B (or T)(mm)
8

9

10

11

12

13

14

15

16

17

18

19

20
Clear
Basic Load Rating Cr (Dynamic)(N)
5350

5400

5800

6100

6400

8000

8650

10800

11300

14500

16200

22500

29700

35500

39500

41500
Clear
Filter by CAD data type
- 2D
- 3D
Clear

Filter by standard shipping days

All

Same day

5 Days or Less
Reset

Optional Attributes

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Variation of this product

Part Number
B7001
B7002
B7003
B7004
B7005
B7006

Standard Unit Price	Minimum order quantity	Volume Discount	Standard Shipping Days ?	RoHS	I.D. d (φ)	O.D. D (φ)	Width B (or T) (mm)	Basic Load Rating Cr (Dynamic) (N)	Allowable Rotational Speed (1/min)	Basic Load Rating Cor (Static) (N)
8.82 €	1	Available	Same day Stock	10	12	28	8	5800	20800	2980
8.57 €	1	Available	Same day Stock	10	15	32	9	6100	18400	3450
8.82 €	1	Available	5 Days	10	17	35	10	6400	16800	3800
9.32 €	1	Available	Same day Stock	10	20	42	12	10800	14400	6600
10.07 €	1	Available	5 Days	10	25	47	12	11300	12800	7400
12.46 €	1	Available	5 Days	10	30	55	13	14500	10400	10100