YAMAWA MFG Screw-Hole-Related Tools
Search by sub-category
Hand Taps
Spiral Taps
Point Taps
Roll Taps
Taps for Pipes
Thread Cutters
Thread-Cutting-Related Tools
Dies
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
- Promotional pricing
Hand Tap HT (Cutting Tap)
YAMAWA MFG
Hand tap used for general tapping work.
[Features]
・ High blade tip strength makes it easy for regrinding.
・ More suitable for manual work compared to taps of other shapes.
・ 2 types are available, with 5P or 1.5P chamfered threads.
・ When machining a blind hole manually, finish machining with 1.5P is recommended after first machining with 5P.
・ Machining with mechanical machinery is also possible.
・ Has straight grooves out of consideration for cutting chip stow.
・ Suitable for work materials whose cutting chips are powder or small coiled close to the powder.
[Applications]
・ Ideal for threading SPC/SPH and other thin plates or SS400/S20 or below mild steel.- Volume Discount
- Stock
Starting from∗ ： 6.44 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Spiral Tap For High Carbon Steel, Oxidation Treatment HC+SP-OX / HC-SP-OX
YAMAWA MFG
Suitable for tapping high carbon steel like S55C etc. Has undergone oxidation treatment.- Volume Discount
Starting from∗ ： 11.36 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
- Promotional pricing
Spiral Flute Tap SP (N-SP)
YAMAWA MFG
The spiral flute tap is ideal for machining blind holes as cutting chip is discharged from the grooves twisted in the same direction as the threads.
[Features]
・ The grooves are twisted in the same direction as the threads for not only good scrap discharging performance but also great cutting performance.
・ Intermittent cutting of female threads with keyway is also possible.
・ Capable of machining both synchronously and asynchronously.
・ Ideal for machining blind holds as the groove is twisted, continuous small coiled scraps are discharged to the rear, and it does not cause cutting chip clogging.
・ Ideal for tapping especially sticky work materials, plastics, etc. due to its sharpness.
・ The tap can easily cut.
・ Intermittent cutting of pilot holes with keyway is also possible.
・ Since the blade strength is inferior to HT, the HT shape is more suitable for hard materials.
[Applications]
・ Ideal for machining blind holes.- Volume Discount
Starting from∗ ： 8.94 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Titanium coating point tab PO-V (N-PO-V)
YAMAWA MFG
Coated point tap suitable for low carbon steel to high carbon steel machining.
[Features]
· Since it has a coating, stable processing is possible at medium cutting speeds, and the tool life is improved.
[Applications]
· Can process both synchronously and asynchronously.
· Recommended for machining speeds of 10 to 20 m/min (completely synchronous feeding recommended for speeds of 15 m/min or higher).- Volume Discount
Starting from∗ ： 25.02 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Tap with Nickel Base Alloy ZEN-P
YAMAWA MFG
A type for machining nickel-base alloys, made from a nickel principal component for corrosion and heat resistance that is significantly superior to that of steel.- Volume Discount
Starting from∗ ： 21.37 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Plus Series Spiral Tap +SP (N+SP)
YAMAWA MFG
A spiral tap suitable for medium- to high-speed machining with machining centers, etc.
[Features]
· Optimal design of the threads allow burdens of machining on each biting blade to be reduced, resulting reduction of machining torque as well as enhancement of wear resistance.
[Applications]
· Can be machined at 10 to 15 m/min using a machining center (fully-synchronized feeding recommended).- Volume Discount
Starting from∗ ： 10.29 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Point Tap PO(N-PO)
YAMAWA MFG
A point tap convenient for through-hole machining as scraps are ejected forward.
[Features]
· Slanting the groove on the cutting edge of the biting part pushes the scraps forward.
· Minimal scrap issues.
· Low cutting torque.
· Capable of machining both synchronously and asynchronously.
[Applications]
· Ideal for machining through-holes.
* N-PO models will transition to PO as soon as stock runs out.- Volume Discount
Starting from∗ ： 15.26 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
For Parallel Screw for Pipe (Hard) CT-PS
YAMAWA MFG
The main purpose of this product is to ensure the tightness of the threaded section when joining pipe parts, etc. This is a hand tap for parallel pipe threads made of carbide, suitable for mass production with hard and brittle materials such as cast iron. Machined PS internal threads are mated with PT external threads. [Features] Chamfer 3.5P; straight fluted carbide hand tap.Starting from∗ ： 177.64 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
Carbide Tap for High Hardness Steel EH-CT
YAMAWA MFG
Ideal for tapping of high hardness steels 45 to 55 HRC, and hot die steels (SKS3, such as SKD11) Female screws with a maximum internal diameter of 6H are recommended for pilot holes.Starting from∗ ： 110.69 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Carbide Hand Tap for Light Alloys N-CT LA
YAMAWA MFG
A carbide tap suitable for thread cutting with aluminum casting (AC), aluminum die castings (ADC), zinc die castings (ZDC), etc.Starting from∗ ： 106.83 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
Carbide Tap for Ultra High Hardness Steel UH-CT
YAMAWA MFG
[SKD material] [Prehardened] Ideal for tapping 55 to 60 HRC (Max: 63 HRC). The machined length of the screw is 1.5 D or less, and the biting length is 5 threads for long life. We recommend using the maximum value 6H female thread bore for the pilot hole diameter.Starting from∗ ： 99.90 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Hand Tap for Difficult-to-Cut Materials EH-HT
YAMAWA MFG
Suitable for tapping high-hardness steels of 35 to 45 HRC such as high carbon steel, alloy steel forgings, tempering material, mold material, etc.- Volume Discount
Starting from∗ ： 16.23 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Carbide-Spiral Tap N-CT-SP
YAMAWA MFG
[Features]
· A carbide spiral tap; ideal for mass-production tapping of materials such as aluminum casting (AC), aluminum die casting (ADC) and zinc diecasting (ZDC).Starting from∗ ： 107.98 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
HD Series Dry Machining Spiral Tap for Carbon Steel / Alloy Steel HDISP
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform both mist and dry machining. Suitable for blind holes on carbon steel and alloy steel, processing in vertical and horizontal directions.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
HF Spiral Tap for Through Holes Used in Series Dry Machining of Carbon / Alloy Steel HDISL
YAMAWA MFG
We have adopted the side through-hole shape by dry machining and ultra-high-speed machining.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
HF Series Ultra-High Speed Spiral Tap for Cast Aluminum / Die Cast Aluminum HFAHS
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform ultra high speed machining. It is suitable for blind hole such as cast aluminum, and it is for the vertical direction processing.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
HF Series Ultra-High Speed Spiral Tap for Cast Aluminum / Die Cast Aluminum HFASP
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform ultra high speed machining. It is suitable for blind hole such as cast aluminum, and it is for the horizontal direction processing.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
HF Series Ultra-High Speed Spiral Tap for Carbon Steel / Alloy Steel HFIHS
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform ultra high speed machining. It is suitable for blind hole of alloy steel, carbon steel, and it is for the vertical direction processing.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
HF Series Ultra-High Speed Spiral Tap for Carbon Steel / Alloy Steel HFISP
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform ultra high speed machining. It is suitable for blind hole of alloy steel, carbon steel, and it is for the horizontal direction processing.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 7 Days *Unit price with basic configuration
-
H Series Dry Machining Spiral Tap for Cast Aluminum / Die Cast Aluminum HDASP
YAMAWA MFG
Uses a center through hole shape that supports internally lubricating machines, and can perform both mist and dry machining. Suitable for blind holes on aluminum castings, processing in vertical and horizontal directions.- Volume Discount
Starting from∗ ： 36.15 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
MC - Helical Cutter MC-HLC
YAMAWA MFG
A screw processing tool that utilizes the "helical feed" function. Female threading of different diameters can be done with a single tool, provided the pitch is the same, and either right- or left-handed female screws can be machined.Starting from∗ ： 253.22 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
Axe Tap AXE-HT
YAMAWA MFG
The blade shape adopted is less prone to damage during machining of aluminum alloy castings, etc. Achieves a longer life.Starting from∗ ： 793.64 € Min. Shipping Days ： 9 Days *Unit price with basic configuration
-
Spiral Tap for Aluminum AL+SP / AL-SP
YAMAWA MFG
A tap that enables high speed, stable machining of light alloys such as aluminum die casting or forged aluminum.
[Features]
· Optimal blade design limits the internal diameter burrs that tend to appear when cutting threads into light alloy.
· Stable, clean thread machining can be performed.
[Applications]
· Stable thread machining of light alloy such as aluminum die casting or forged aluminum at high speed.
· Can be used not only with aluminum, but also other materials such as brass, bronze, magnesium castings, and zinc alloy castings.- Volume Discount
Starting from∗ ： 11.86 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Short Chamfer Torqueless Roll Taps SC-TL-RZ
YAMAWA MFG
The number of chamfer threads is just 1, creating a roll tap with specially shaped threading parts for achieving low torque use.- Volume Discount
Starting from∗ ： 29.71 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Short Spiral Tap for Stainless Steel SU-S-SP
YAMAWA MFG
[Features]
· For blind hole processing in materials with high hardening properties and extreme viscosity such as stainless steel, chrome steel and molybdenum steel.- Volume Discount
Starting from∗ ： 15.69 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Spiral Tap for Stainless Steel SU+SP / SU-SP
YAMAWA MFG
Spiral tap for blind hole machining with extremely viscous or work-hardened work material.
[Features]
· For blind hole machining with extremely viscous or work-hardened work materials such as chrome steel, molybdenum steel, and stainless steel.
· Optimal design of the screw part reduces the machining burden on each blade bite, reducing the cutting resistance and increasing tool life.
· Stable scrap is ejected and a good finish is realized.
· Capable of machining both synchronously and asynchronously.
· Machining speed of 10 m/min or less is recommended.
[Applications]
Optimal for machining extremely viscous or work-hardened work material.- Volume Discount
Starting from∗ ： 11.81 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
- Promotional pricing
Stainless Steel Hand Tap SU-HT
YAMAWA MFG
Hand tap suitable for machining extremely viscous or work-hardened work material.
[Features]
Optimal blade design is suitable for machining chrome steel, molybdenum steel, and stainless steel.
· 2 types are available, with 4P or 1.5P biting threads, to suit the application used.
· Capable of machining both synchronously and asynchronously.
· Machining speed of 5 m/min or less is recommended.
[Applications]
Ideal for machining with extremely viscous or work-hardened work materials such as chrome steel, molybdenum steel, and stainless steel.- Volume Discount
Starting from∗ ： 8.89 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
- Promotional pricing
Stainless Steel Point Tap SU+PO / SU-PO
YAMAWA MFG
Point tap for through-hole machining with extremely viscous or work-hardened work material.
[Features]
Optimal blade design is suitable for machining chrome steel, molybdenum steel, and stainless steel.
· Capable of machining both synchronously and asynchronously.
· Machining speed of 10 m/min or less is recommended.
[Applications]
· Ideal for machining through-holes with chrome steel, molybdenum steel, and stainless steel.- Volume Discount
Starting from∗ ： 12.22 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Spiral Tap for Stainless Steel Through Holes SU+SL
YAMAWA MFG
Work hardening in blind hole processing of significantly gummy materials, from stainless steel and chrome steel to molybdenum steel. Processable in mid-speed range of 10 M/MIN ~ 20 M/MIN.Starting from∗ ： 11.86 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Titanium Coating Roll Tap R+V / R-V
YAMAWA MFG
A coating roll tap suitable for threading steel and nonferrous materials.- Volume Discount
Starting from∗ ： 25.23 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Titanium Coated Through Hole Spiral Tap AU+SL
YAMAWA MFG
Coated Spiral Tap For Through Hole Drilling Suited For Stable Mid-Speed (10 to 25m/minute) Threading in Both Synchronous and Asynchronous Machining- Volume Discount
Starting from∗ ： 21.06 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Spiral Tap for Titanium Alloy, for Through Hole ZET-P
YAMAWA MFG
A tap for processing high strength, lightweight, and heat-resistant titanium alloys, where the main component is titanium.- Volume Discount
Starting from∗ ： 21.37 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap for Titanium Alloy ZET-B
YAMAWA MFG
A tap for processing high strength, lightweight, and heat-resistant titanium alloys, where the main component is titanium.- Volume Discount
Starting from∗ ： 21.37 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Dry Processing Roll Tap OL+RZ / OL-RZ
YAMAWA MFG
It is a roll tap that's capable of tapping without lubrication for burred thin iron plates and steel with relatively short processing length at the size of M6 or less.- Volume Discount
Starting from∗ ： 27.00 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Nut Tap NT
YAMAWA MFG
Straight nut tap mainly used for machining nuts using a tapping machine.- Volume Discount
Starting from∗ ： 44.09 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap for Nickel Base Alloy ZEN-B
YAMAWA MFG
A type for machining nickel-base alloys, made from a nickel principal component for corrosion and heat resistance that is significantly superior to that of steel.- Volume Discount
Starting from∗ ： 21.37 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
High Performance Roll Tap HP+ RZ / HP-RZ
YAMAWA MFG
It is suitable for processing steel materials (35 HRC or less) and light alloys, and can support high-speed machining (20-50 m/min)- Volume Discount
Starting from∗ ： 24.43 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Hand Tap for Left-Hand Threads HT(LH)
YAMAWA MFG
It is suitable for threading for simple installation used for thin steel plates such as SPC and SPH and mild steel of SS400, S20 or less.- Volume Discount
Starting from∗ ： 21.36 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Coating Spiral Tap AU+ SP
YAMAWA MFG
Coating spiral tap with blind holes has a screw part that leaves behind complete threads and its special form sweeps away half of the screw threads afterwards + unique groove form helps maintain the discharge of scraps and has achieved in reducing friction.- Volume Discount
Starting from∗ ： 21.66 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Plus Series Point Tap +PO (N+PO)
YAMAWA MFG
* N+SP will be replaced with +SP as soon as there is no more in stock.- Volume Discount
Starting from∗ ： 10.30 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Starting from∗ ： 115.00 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Long Shank Spiral Tap LS-SP(LS-N-SP)
YAMAWA MFG
* LS-N-SP will switch to LS-SP as soon as the stock runs out.- Volume Discount
Starting from∗ ： 19.63 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Long Shank Titanium Coated Spiral Tap LS-SP-V(LS-N-SP-V)
YAMAWA MFG
* LS-N-SP-V will switch to LS-SP-V as soon as the stock runs out.- Volume Discount
Starting from∗ ： 37.13 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Long Shank Titanium Coated Point Tap LS-PO-V(LS-N-PO-V)
YAMAWA MFG
* LS-N-PO-V will switch to LS-PO-V as soon as the stock runs out.- Volume Discount
Starting from∗ ： 37.13 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
For Tapered Screw for Pipe (Short Screw Type) S-PT
YAMAWA MFG
A cutting tap used for screw tapping in connecting pipes and pipe parts where the main purpose is mechanical connection. Can be used for machining tapered threads requiring durability such as water pipes and gas pipes- Volume Discount
Starting from∗ ： 21.41 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days ： |
| Specifications |
| Screw Types |
| Screw size (Nominal) |
| Pitch (P), Number of Threading(mm) |
| Chamfer threads (Lcf) |
| Tool Material Type |
| work material |
| Tap Type |
| Hole type |
| Coating Y/N |
| Coating Type |
| Overall Length (L)(mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG | YAMAWA MFG |
| Product Series | Spiral Tap For High Carbon Steel, Oxidation Treatment HC+SP-OX / HC-SP-OX | HD Series Dry Machining Spiral Tap for Carbon Steel / Alloy Steel HDISP | HF Spiral Tap for Through Holes Used in Series Dry Machining of Carbon / Alloy Steel HDISL | HF Series Ultra-High Speed Spiral Tap for Cast Aluminum / Die Cast Aluminum HFAHS | HF Series Ultra-High Speed Spiral Tap for Cast Aluminum / Die Cast Aluminum HFASP | HF Series Ultra-High Speed Spiral Tap for Carbon Steel / Alloy Steel HFIHS | HF Series Ultra-High Speed Spiral Tap for Carbon Steel / Alloy Steel HFISP | H Series Dry Machining Spiral Tap for Cast Aluminum / Die Cast Aluminum HDASP | |||||||||||||||||||||||||||||||||||||
| Starting from∗ | 6.44 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 11.36 € *Unit price with basic configuration Volume Discount | 8.94 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 25.02 € *Unit price with basic configuration Volume Discount | 21.37 € *Unit price with basic configuration Volume Discount | 10.29 € *Unit price with basic configuration Volume Discount | 15.26 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 177.64 € *Unit price with basic configuration | 110.69 € *Unit price with basic configuration | 106.83 € *Unit price with basic configuration | 99.90 € *Unit price with basic configuration | 16.23 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 107.98 € *Unit price with basic configuration | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 36.15 € *Unit price with basic configuration Volume Discount | 253.22 € *Unit price with basic configuration | 793.64 € *Unit price with basic configuration | 11.86 € *Unit price with basic configuration Volume Discount | 29.71 € *Unit price with basic configuration Volume Discount | 15.69 € *Unit price with basic configuration Volume Discount | 11.81 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 8.89 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 12.22 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 11.86 € *Unit price with basic configuration | 25.23 € *Unit price with basic configuration Volume Discount | 21.06 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 21.37 € *Unit price with basic configuration Volume Discount | 21.37 € *Unit price with basic configuration Volume Discount | 27.00 € *Unit price with basic configuration Volume Discount | 44.09 € *Unit price with basic configuration | 21.37 € *Unit price with basic configuration Volume Discount | 24.43 € *Unit price with basic configuration Volume Discount | 21.36 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 21.66 € *Unit price with basic configuration Volume Discount | 10.30 € *Unit price with basic configuration Volume Discount | 115.00 € *Unit price with basic configuration | 19.63 € *Unit price with basic configuration Volume Discount | 37.13 € *Unit price with basic configuration Volume Discount | 37.13 € *Unit price with basic configuration Volume Discount | 21.41 € *Unit price with basic configuration Volume Discount |
| Min. Shipping Days ： | Same day | 8 Days | Same day | 6 Days | 6 Days | 6 Days | Same day | 8 Days | 6 Days | 7 Days | 6 Days | Same day | 7 Days | 8 Days | 8 Days | 7 Days | 8 Days | 8 Days | 7 Days | 8 Days | 8 Days | 9 Days | 6 Days | 6 Days | 6 Days | Same day | Same day | Same day | 6 Days | 6 Days | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 8 Days | 8 Days |
| Specifications |
| ||||||||||||||||||||||||||||||||||||||||||||
| Screw Types | Meter / Unified / Sewing Machine | Meter | Meter | Meter | Meter | Meter | Meter / Unified | Parallel for Pipes | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter / Taper for Pipe / Parallel for Pipes | Meter | Meter | Meter | Meter | Meter / Unified / Whitworth | Meter | Meter / Unified / Whitworth | Meter | Meter | Meter | Meter | Meter | Meter / Unified | Meter | Meter | Meter / Unified | Meter | Meter | Meter | Meter / Miniature | Meter / Unified / Whitworth | Meter | Meter | Taper for Pipe |
| Screw size (Nominal) | No.0-80UNF ～ M48 | M3 ～ M16 | M3 ～ M12 | M3 ～ M12 | M3 ～ M20 | M2 ～ M6 | No.10-32UNF ～ M24 | 1´-11 ～ 3/8-19 | M3 ～ M12 | M1.4 ～ M20 | M2 ～ M20 | M5 ～ M8 | M3 ～ M20 | M6 ～ M20 | M6 ～ M20 | M6 ～ M20 | M6 ～ M20 | M6 ～ M20 | M6 ～ M20 | M6 ～ M20 | 1015 ～ 32506N300M | M6 ～ M12 | M2 ～ M16 | M1 ～ M6 | M3 ～ M20 | No.10-32UNF ～ M45 | M3 ～ M6 | No.10-32UNF ～ M42 | M3 ～ M6 | M1 ～ M6 | M3 ～ M12 | M3 ～ M20 | M3 ～ M20 | No.10-32UNF ～ M6 | M8 | M3 ～ M20 | No.10-32UNF ～ M20 | M2.5 ～ M8 | M2 ～ M12 | M3 ～ M6 | S0.2 ～ M5 | 1'-8UNC ～ M36 | M3 ～ M12 | M3 ～ M12 | 1′-11 ～ 3/8-19 |
| Pitch (P), Number of Threading(mm) | 0.2 ～ 7 | 0.5 ～ 2 | 0.5 ～ 1.25 | 0.5 ～ 1.75 | 0.5 ～ 2.5 | 0.4 ～ 1 | 0.75 ～ 2 | 19 | 0.5 ～ 1.75 | 0.3 ～ 2.5 | 0.4 ～ 2.5 | 0.8 ～ 1.25 | 0.5 ～ 2.5 | 1 ～ 1.75 | 1 ～ 1.75 | 1 ～ 1.75 | 1 ～ 1.75 | 1 ～ 1.75 | 1 ～ 1.75 | 1 ～ 1.75 | - | 1 ～ 1.75 | 0.4 ～ 2 | 0.2 ～ 1 | 0.5 ～ 2.5 | 0.3 ～ 4.5 | 0.5 ～ 1 | 0.3 ～ 4.5 | 0.5 ～ 1 | 0.25 ～ 1 | 0.5 ～ 1.75 | 0.5 ～ 2.5 | 0.5 ～ 2.5 | 0.25 ～ 1 | 1.25 | 0.5 ～ 2.5 | 0.25 ～ 1.75 | 0.35 ～ 0.75 | 0.4 ～ 1.75 | 0.5 ～ 1 | 0.25 ～ 0.5 | 1 ～ 4 | 0.5 ～ 1.75 | 0.5 ～ 1.75 | - |
| Chamfer threads (Lcf) | 1.5P ～ 5P | 2.5P | 2.5P | 5P | 4.5P | 2.5P | 5P | 3.5P | 5P | 1.5P ～ 5P | 5P | 5P | 2.5P | 2.5P | 5P | 2.5P | 2.5P | 2.5P | 2.5P | 2.5P | - | 1.5P | 2.5P | 1P | 2.5P | 2.5P | 1.5P ～ 4P | 5P | 5P | 2P ～ 4P | 5P | 5P | 3P | 4P | 24P | 3P | 2P ～ 4P | 5P | 2.5P | 5P | - | 2.5P | 2.5P | 5P | 2.5P |
| Tool Material Type | High-speed steel | High-speed steel | High-speed steel | High-speed steel | Powder high-speed steel | High-speed steel | High-speed steel | Carbide | Carbide | Carbide | Carbide | Cobalt HSS | Carbide | Cobalt HSS | Cobalt HSS | Cobalt HSS | Cobalt HSS | Cobalt HSS | Cobalt HSS | Cobalt HSS | Cobalt HSS | Powder high-speed steel | High-speed steel | Powder high-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | Powder high-speed steel | Powder high-speed steel | Powder high-speed steel | High-speed steel | Powder high-speed steel | Powder high-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel | High-speed steel |
| work material | Medium carbon steel (carbon content 0.25 to 0.45%)[○/◎] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Cast Iron (FC)[○/◎] / Ductile Cast Iron (FCD)[○/◎] / Brass (Bs)[○] / Brass cast iron (BsC)[○/◎] / Bronze (Pb)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Quenched and tempered steel (45 to 55 HRC)[○] | Copper (Cu)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | High Hardness Steel (50-60 HRC)[○] | Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Ductile Cast Iron (FCD)[○] | Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] | Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] | Cast Iron (FC)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Copper (Cu)[○/◎] / Brass (Bs)[○/◎] / Brass cast iron (BsC)[○/◎] / Bronze (Pb)[○/◎] / Aluminum Rolled Material (AL)[○/◎] / Aluminum Alloy Casting (AC, ADC)[○/◎] / Magnesium Alloy (MC)[○/◎] / Zinc Alloy Casting (ZDC)[○/◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] | High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○/◎] / Stainless Steel (JIS-SUS)[○/◎] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Steel casting (SC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Steel casting (SC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Copper (Cu)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] | High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | - | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Nickel-based alloy (Inconel, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○/◎] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | - | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] |
| Tap Type | Hand Tap | Spiral Tap | Spiral Tap | Point tap | Point tap | Spiral Tap | Point tap | Tap for pipes | Point tap | Hand Tap | Point tap | Hand Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Thread cutter | Hand Tap | Spiral Tap | Roll tap | Spiral Tap | Spiral Tap | Hand Tap | Point tap | Spiral Tap | Roll tap | Spiral Tap | Spiral Tap | Spiral Tap | Roll tap | Point tap | Spiral Tap | Roll tap | Hand Tap | Spiral Tap | Point tap | Die | Spiral Tap | Spiral Tap | Point tap | Tap for pipes |
| Hole type | For through hole / For blind hole | For blind hole | For blind hole | For through hole | For through hole | For blind hole | For through hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole / For blind hole | For through hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole / For blind hole | For through hole / For blind hole | - | For through hole / For blind hole | For blind hole | For blind hole | For blind hole | For blind hole | For through hole / For blind hole | For through hole | For through hole | For through hole / For blind hole | For through hole | For through hole | For blind hole | For through hole | For through hole | For blind hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole / For blind hole | - | For blind hole | For blind hole | For through hole | For through hole / For blind hole |
| Coating Y/N | N/A | N/A | N/A | Available | N/A | N/A | N/A | N/A | Available | N/A | Available | N/A | N/A | Available | Available | Available | Available | Available | Available | Available | Available | Available | N/A | Available | N/A | N/A | N/A | N/A | N/A | Available | Available | N/A | N/A | Available | N/A | N/A | Available | N/A | Available | N/A | N/A | N/A | N/A | Available | N/A |
| Coating Type | - | - | - | TiN | - | - | - | - | TiAlN | - | TiAlN | - | - | TiCN | TiCN | TiCN | TiCN | TiCN | TiCN | TiCN | TiN | TiN | - | TiCN | - | - | - | - | - | TiN | TiN | - | - | TiCN | - | - | TiCN | - | TiN | - | - | - | - | TiN | - |
| Overall Length (L)(mm) | 36 ～ 185 | 46 ～ 95 | 46 ～ 82 | 46 ～ 82 | 46 ～ 105 | 42 ～ 62 | 60 ～ 120 | 55 ～ 95 | 46 ～ 82 | 34 ～ 105 | 40 ～ 105 | 60 ～ 70 | 46 ～ 105 | 62 ～ 105 | 62 ～ 105 | 62 ～ 105 | 62 ～ 105 | 62 ～ 105 | 62 ～ 105 | 62 ～ 105 | 70 ～ 200 | 62 ～ 82 | 42 ～ 95 | 36 ～ 62 | 46 ～ 105 | 36 ～ 180 | 46 ～ 62 | 36 ～ 175 | 46 ～ 62 | 36 ～ 62 | 46 ～ 82 | 46 ～ 105 | 46 ～ 105 | 36 ～ 62 | 140 | 46 ～ 105 | 36 ～ 105 | 46 ～ 70 | 42 ～ 82 | 46 ～ 62 | - | 100 ～ 300 | 100 ～ 150 | 100 ～ 150 | 55 ～ 155 |
Loading...
Filter by:
Stock
-
- Stock Items Included
Narrow search by specifying spec./dim.
-
Screw Types
-
Screw size (Nominal)
- CTG-54
- CTG-42
- CTG-36
- CTG-28
- CTG-22
- CTG-16
- No0UN
- NO.0-80UNF
- No.0-80UNF
- No.10
- S0.1
- NO.1-72UNF
- No.1-72UNF
- NO.1-64UNC
- No.1-64UNC
- NO.10-32UNF
- No.10-32UNF
- NO.10-24UNC
- No.10-24UNC
- No.12
- No.12-32UNEF
- NO.12-28UNF
- No.12-28UNF
- NO.12-24UNC
- No.12-24UNC
- No.2
- S0.2
- NO.2-64UNF
- No.2-64UNF
- NO.2-56UNC
- No.2-56UNC
- No.3
- S0.3
- NO.3-56UNF
- No.3-56UNF
- NO.3-48UNC
- No.3-48UNC
- No.4
- S0.4
- NO.4-48UNF
- No.4-48UNF
- NO.4-40UNC
- No.4-40UNC
- No.5
- S0.5
- NO.5-44UNF
- No.5-44UNF
- NO.5-40UNC
- No.5-40UNC
- No.6
- S0.6
- NO.6-40UNF
- No.6-40UNF
- No.6-32UNC
- S0.7
- No.8
- S0.8
- NO.8-36UNF
- No.8-36UNF
- NO.8-32UNC
- No.8-32UNC
- S0.9
- 1"
- 1UN
- 1UNS
- G1
- G 1"
- M1
- NPS1
- NPT1
- NPTF1
- No1UN
- PF1
- PF 1
- PT 1
- R1
- Rp1
- S1
- UNC 1
- UNC 1"
- UNF 1"
- W1
- 1´-20UNEF
- 1´-14UNS
- 1'-12UNF
- 1´-12UNF
- 1´-11
- 1′-11
- 1-8UNC
- 1'-8UNC
- 1´-8UNC
- G1"-3"
- 1"1/2UN
- 1"1/2
- G1"1/2
- NPS1"1/2
- NPT1"1/2
- R1"1/2
- Rp1"1/2
- W1"1/2
- 1´1/2-11
- 1′1/2-11
- 1 1/2-8UN
- 1"1/4UN
- 1"1/4
- G1"1/4
- NPS1"1/4
- NPT1"1/4
- R1"1/4
- Rp1"1/4
- W1"1/4
- 1´1/4-11
- 1′1/4-11
- 1 1/4-8UN
- 1"1/8UN
- G1"1/8
- R1"1/8
- W1"1/8
- 1 1/8-8UN
- 1´ 1/8-7UNC
- 1"1/16UN
- 1/2
- 1/2UN
- G1/2
- G 1/2
- NPS1/2
- NPT1/2
- NPTF1/2
- PF 1/2
- PT 1/2
- R1/2
- Rc1/2
- Rp1/2
- UNC 1/2
- UNF 1/2
- UNJF 1/2
- W1/2
- 1/2-28UNEF
- 1/2-20UNF
- 1/2-14
- 1/2-13UNC
- G1/2 5/8
- 1/2W12
- 1 3/4
- 1"3/4UN
- G1"3/4
- R1"3/4
- Rp1"3/4
- W1"3/4
- 1′3/4-11
- 1 3/4-8UN
- 1 3/8
- 1"3/8UN
- G1"3/8
- R1"3/8
- W1"3/8
- 1 3/8-8UN
- 1/4
- 1/4UN
- G1/4
- G 1/4
- NPS1/4
- NPT1/4
- NPTF1/4
- PF1/4
- PF 1/4
- PS 1/4
- PT 1/4
- R1/4
- Rc1/4
- Rp1/4
- SM1/4
- UNC 1/4
- UNF 1/4
- UNJF 1/4
- W1/4
- 1/4-32UNEF
- 1/4-28UNF
- 1/4-20UNC
- 1/4-19
- 1/4W20
- W1"5/8
- 1 5/8-8UN
- W1"7/8
- 1 7/8-8UN
- 1'W8
- 1/8
- G1/8
- G 1/8
- NPS1/8
- NPT1/8
- NPTF1/8
- PF1/8
- PF 1/8
- PT 1/8
- R1/8
- Rc1/8
- Rp1/8
- SM1/8
- W1/8
- 1/8-28
- 1/8SM40
- 1/8SM44
- 1/16
- G1/16
- NPS1/16
- NPT1/16
- R1/16
- Rp1/16
- 1/16-28
- 1/16SM80
- M1.1
- G 1.1/2
- G 1.1/4
- G 1.1/8
- M1.2
- S1.2
- M1.4
- S1.4
- M1.6
- M1.7
- M1.8
- 2"
- 2UN
- G2
- M2
- M2.0
- NPS2
- NPT2
- No2UN
- R2
- Rp2
- UNC 2
- UNF 2
- W2
- 2´-11
- 2′-11
- 2-8UN
- G2"1/2
- R2"1/2
- Rp2"1/2
- 2′1/2-11
- W2"1/4
- M2.2
- M2.3
- M2.5
- M2.6
- 3M
- EGM 3
- G3
- M3
- M3.0
- No3UN
- R3
- Rp3
- STI M3
- UNC 3
- UNF 3
- 3′-11
- G3"1/2
- R3"1/2
- Rp3"1/2
- 3/4
- 3/4UN
- G3/4
- G 3/4
- NPS3/4
- NPT3/4
- NPTF3/4
- PF 3/4
- R3/4
- Rp3/4
- UNC 3/4
- UNF 3/4
- W3/4
- 3/4-20UNEF
- 3/4-16UNF
- 3/4-14
- 3/4-10UNC
- 3/4W10
- 3/8
- 3/8UN
- G3/8
- G 3/8
- NPS3/8
- NPT3/8
- NPTF3/8
- PF3/8
- PF 3/8
- PT 3/8
- R3/8
- Rc3/8
- Rp3/8
- UNC 3/8
- UNF 3/8
- UNJF 3/8
- W3/8
- 3/8-32UNEF
- 3/8-24UNF
- 3/8-19
- 3/8-16UNC
- 3/8W16
- M3 - M10
- M3～10
- M3 - M12
- SM3/16
- W3/16
- 3/16SM24
- 3/16W24
- 3/16SM28
- 3/16SM32
- 3/16SM40
- M3 - M18
- SM3/32
- 3/32SM56
- 3/32SM100
- 3.5
- M3.5
- 4
- 4M
- EGM 4
- G4
- M4
- M4.0
- MF4
- No4UN
- R4
- Rp4
- STI M4
- UNC 4
- UNF 4
- №4-40UNC
- M4～6
- M4.5
- 5M
- EGM 5
- M5
- M5.0
- MF5
- No5UN
- STI M5
- UNC 5
- №5-40UNC
- 5/8
- 5/8UN
- G5/8
- G 5/8
- NPS5/8
- R5/8
- UNC 5/8
- UNF 5/8
- W5/8
- 5/8-24UNEF
- 5/8-18UNF
- 5/8-11UNC
- G5/8 3/4
- 5/8W11
- M5 - M12
- M5～13
- 5/16
- 5/16UN
- UNC 5/16
- UNF 5/16
- UNJF 5/16
- W5/16
- 5/16-32UNEF
- 5/16-24UNF
- 5/16-18UNC
- 5/16W18
- W5/32
- 5/64SM64
- 5.5M
- M5.5
- 6
- EGM 6
- M6
- M6.0
- MF6
- No6UN
- STI M6
- UNC 6
- UNF 6
- UNJC 6
- No6-40UNF
- №6-32UNC
- M7
- MF7
- PG7
- 7 execution M3 - M12
- 7/8
- 7/8UN
- G7/8
- G 7/8
- NPS7/8
- R7/8
- UNC 7/8
- UNF 7/8
- W7/8
- 7/8-20UNEF
- 7/8-14UNF
- 7/8-9UNC
- 7/8W9
- 7/16
- 7/16UN
- UNC 7/16
- UNF 7/16
- UNJF 7/16
- W7/16
- 7/16-28UNEF
- 7/16-20UNF
- 7/16-14UNC
- 7/16W14
- SM7/32
- 7.5
- M7.5
- EGM 8
- M8
- MF8
- No8UN
- STI M8
- Tr8
- UNC 8
- UNF 8
- UNJC 8
- №8-32UNC
- 9
- M9
- PG9
- 9/16
- 9/16UN
- UNC 9/16
- UNF 9/16
- 9/16-18UNF
- 9/16-12UNC
- 9/16W12
- SM9/32
- SM9/64
- 9/64SM40
- M9.5
- EGM 10
- M10
- MF10
- No10UN
- STI M10
- Tr10
- Tr 10
- UNC10
- UNC 10
- UNF 10
- UNJF 10
- №10-32UNF
- №10-24UNC
- M10～25
- M11
- PG11
- SM11/32
- SM11/64
- 11/64SM40
- EGM 12
- M12
- MF12
- Mf12
- No12UN
- STI M12
- Tr12
- Tr 12
- UNC 12
- UNF 12
- M12 x 1.5
- M13
- PG13.5
- M14
- MF14
- Tr 14
- M15
- SM15/64
- 15/64SM28
- M16
- MF16
- Mf16
- PG16
- Tr16
- Tr 16
- M16 x 1.5
- M17
- M18
- MF18
- Tr18
- Tr 18
- M19
- M20
- MF20
- Mf20
- Tr 20
- M20 x 1.5
- M21
- PG21
- M22
- M22X
- MF22
- Tr 22
- M23
- M24
- M24X
- MF24
- Tr 24
- M25
- M25X
- MF25
- Mf25
- Tr 25
- M25 x 1.5
- M26
- MF26
- Tr 26
- M27
- MF27
- M28
- MF28
- Tr 28
- PG29
- M30
- MF30
- Tr 30
- M32
- Mf32
- M33
- M34
- M35
- M36
- PG36
- M37
- M38
- M39
- M40
- M42
- PG42
- M44
- M45
- M46
- M48
- M50
- M52
- M56
- M64
- 1015
- 1020N100M
- 1020N150M
- 06510X28R
- 10154
- 12204
- 12254N100M
- 12254N150M
- 12254N200M
- 16304N100M
- 16304N150M
- 16304N200M
- 16304N250M
- 20305
- 20505N100M
- 20505N150M
- 20505N200M
- 20505N300M
- 20505N350M
- 25506N100M
- 25506N150M
- 25506N200M
- 25506N300M
- 25506N350M
- 32506
- 32506N150M
- 32506N200M
- 32506N300M
- 035083N075M
- 035083N080M
- 040123N100M
- 060163N050M
- 060163N100M
- 060163N125M
- 065103X28G
- 075203N125M
- 075203N150M
- 080153X19G
- 080153X19R
- 080203N050M
- 080203N100M
- 090244N125M
- 090244N175M
- 100254N050M
- 100254N100M
- 100254N150M
- 100254N200M
- 120204X14G
- 120204X14R
- 120304N100M
- 120304N150M
- 120304N200M
- 160264X11G
- 160264X11R
- 160404N150M
- 160404N200M
- 160404N250M
- 200305X11G
- 200305X11R
- 200505N150M
- 200505N200M
- 200505N300M
-
Pitch (P), Number of Threading(mm)
-
Chamfer threads (Lcf)
-
Tool Material Type
- High-speed steel
- Cobalt HSS
- Powder high-speed steel
- Carbide
- Alloy HSS
- Vanadium High-Speed Steel
- JIS-SKS
-
work material
- Low-Carbon Steel (carbon alloy less than 0.25%)
- Medium carbon steel (carbon content 0.25 to 0.45%)
- High Carbon Steel (C with a content over 0.45%)
- Alloy Steel (SCM)
- Stainless Steel (JIS-SUS)
- Quenched and tempered steel (25 to 35 HRC)
- Quenched and tempered steel (35 to 45 HRC)
- Quenched and tempered steel (45 to 55 HRC)
- High Hardness Steel (50-60 HRC)
- Tool Steel (Before SKD Hardening)
- Steel casting (SC)
- Cast Iron (FC)
- Ductile Cast Iron (FCD)
- Copper (Cu)
- Brass (Bs)
- Brass cast iron (BsC)
- Bronze (Pb)
- Aluminum Rolled Material (AL)
- Aluminum Alloy Casting (AC, ADC)
- Magnesium Alloy (MC)
- Zinc Alloy Casting (ZDC)
- Titanium Alloy (Ti-6Al-4V, etc)
- Nickel-based alloy (Inconel, etc.)
- Thermosetting plastic (bakelite, phenol, etc.)
- Thermoplastic plastic (vinyl chloride, nylon, etc.)
-
Tap Type
-
Hole type
-
Coating Y/N
-
Coating Type
-
Overall Length (L)(mm)
Narrow search by specifying Brand
-
- MISUMI (16)
- OSG (377)
- YAMAWA MFG (98)
- CARMEX (35)
- ESCO (25)
- SKC (25)
- TRUSCO NAKAYAMA (24)
- REX TOOLS (20)
- NACHI(FUJIKOSHI) (15)
- ISHIHASHI (13)
- SANDVIK (13)
- GEDORE (7)
- GUHRING (5)
- WERA (5)
- HAZET (4)
- NOGAJAPAN (4)
- TANOI MFG (4)
- RENNSTEIG (3)
- BAHCO (2)
- EIKOSHA (2)
- H & H (2)
- NS TOOL (2)
- RUKO (2)
- WIHA (2)
- FEIN (2)
- BERNSTEIN AG (1)
- ENGINEER (1)
- KANETEC (1)
- LIGHTSEIKI (1)
- MITSUTOMO (1)
- NEW STRONG (1)
- STAHLWILLE (1)
- WALTER PROTOTYP (1)
Narrow search by specifying CAD data type
-
- 2D
- 3D
Categories related to Screw-Hole-Related Tools
Způsob platby
Platba na účet
Zálohová platba
Výroba na vyžádání
Certifikáty
Copyright © MISUMI Corporation Všechna práva vyhrazena.